Configure Networking on Ubuntu

During the installation of Ubuntu on your server an IP address was most likely obtained automatically. This dynamic IP address assignment will need to be changed to a static IP address. This section will cover the simple network configuration changes needed to set a static IP network address for your server. For this section, the directions assume the configuration is for a node with only one interface (eth0) after a default installation.

Note

These instructions assume that the reader is familiar with opening, editing and saving files at the command line. Please consult your OS documentation if you need assistance with these tasks.

Most Linux systems have a few commands that can be used to find out what the current network configuration is, for example:

ifconfig -a

You can also use variations of the ip command:

ip addr

Basic network configuration and hostname on a Ubuntu system are stored in several files which must be edited to create a working configuration:

  • /etc/network/interfaces describes the network interfaces
  • /etc/hostname configures the nameserver credentials
  • /etc/hosts resolves IP addresses to hostnames

Once the new configuration is saved the interface must be restarted.

Debian / Ubuntu Linux restart network interface

To restart network interface, enter:
sudo /etc/init.d/networking restart
To stop and start use the following option (do not run them over remote ssh session as you will get disconnected):
sudo /etc/init.d/networking stop
sudo /etc/init.d/networking start

Debian/Ubuntu Linux with systemd, run:
$ sudo systemctl restart networking

Changing Network Configuration

Below is an example of a static IP configuration on a system with only one Ethernet interface (eth0) and 10.0.0.41/24 for the IP address. Opening the /etc/network/interfaces file will produce:

# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

# The primary network interface
auto eth0
iface eth0 inet static
    address 10.0.0.41
    netmask 255.255.255.0
    network 10.0.0.0
    broadcast 10.0.0.255
    gateway 10.0.0.1
    dns-nameservers 10.0.0.1 8.8.8.8
    dns-domain acme.com
    dns-search acme.com
Open your /etc/network/interfaces file, locate the:
  • "iface eth0..." line and change dynamic to static
  • address line and change the address to the static IP address
  • netmask line and change the address to the correct subnet mask
  • gateway line and change the address to the correct gateway address
  • dns-nameservers line and change (or add) the nameserver information

If you aren't certain which IP address, subnet mask, gateway or dns-nameservers you need, please consult with your network administrator for the correct information.

When you are happy with your configuration restart the interface with the command below. If you are connected using SSH you will lose your connection, re-connect using the new IP address:

ifdown eth0; ifup eth0

Changing the Hostname

To change the hostname to your preferred node name (example: prodnode01), you have to edit the /etc/hostname file:

prodnode01

Adding the FQDN (Hostname)

To ensure your server traffic will be routing correctly add the server's Fully Qualified Domain Name (FQDN) and IP address to the hosts file. Open the /etc/hosts file and add a line with the static IP address and the FQDN, similar to the example shown below:

192.168.0.0 prodnode01.acme.com

With all your files edited and saved, you should reboot so the new name and configuration will be used.

Reboot the system and then use ifconfig or ipaddr to confirm that your new configuration is available. You can also use hostname -f to verify the hostname change,

Configure Networking on CentOS / Red Hat

During the installation of CentOS/Red Hat on your server an IP address was most likely obtained automatically. This dynamic IP address assignment will need to be changed to a static IP address. This section will cover the simple network configuration changes needed to set a static IP network address for your server. For this section, the directions assume the configuration is for a node with only one interface (eth0) after a default installation.

Note

These instructions assume that the reader is familiar with opening, editing and saving files at the command line. Please consult your OS documentation if you need assistance with these tasks.

Most Linux systems have a few commands that can be used to find out what the current network configuration is, for example:

ifconfig -a

You can also use variations of the ip command:

ip addr

Basic network configuration and hostname on a CentOS/Red Hat system are stored in several files which must be edited to create a working configuration:

  • /etc/sysconfig/network specifies routing and host information for all interfaces
  • /etc/sysconfig/network-scripts/ifcfg-ethX contains the configuration scripts for each network interface
  • /etc/resolv.conf configures the nameserver credentials
  • /etc/hosts resolves IP addresses to hostnames

Changing Network Configuration

Name server configuration is in /etc/resolv.conf:

search acme.com
nameserver 10.0.0.1
nameserver 8.8.8.8
Open your /etc/resolv.conf file, locate the:
  • first nameserver line and change the nameserver information
  • second nameserver line and change (or add) the nameserver information

If you aren't certain which nameservers you need, please consult with your network administrator for the correct information.

Below is an example of a static IP configuration on a system with only one Ethernet interface (eth0) and 10.0.0.41/24 for the IP address. Opening the /etc/sysconfig/network-scripts/ifcfg-eth0 file will produce:

DEVICE="eth0"
BOOTPROTO="none"
ONBOOT="yes"
TYPE="Ethernet"
IPADDR=10.0.0.42
NETMASK=255.255.255.0
BROADCAST=10.0.0.255
GATEWAY=10.0.0.1
Open your /etc/network/interfaces file, locate the:
  • BOOTPROTO line and change dhcp to none.
  • IPADDR line and change the address to the static IP address
  • NETMASK line and change the address to the correct subnet mask
  • GATEWAY line and change the address to the correct gateway address

If you aren't certain which IP address, subnet mask or gateway you need, please consult with your network administrator for the correct information.

Changing the Hostname

For a node called prodnode02.acme.com the content of the /etc/sysconfig/network file would look like this:

NETWORKING=yes
HOSTNAME=prodnode02.acme.com

Open your /etc/sysconfig/network file, locate the HOSTNAME line and change the hostname to your preferred node name.

Adding the FQDN (Hostname)

To ensure your hostname and IP address are routing correctly the Fully Qualified Domain Name (FQDN) and IP address should be added to the hosts file. Open the /etc/hosts file:

192.168.0.0 prodnode01.acme.com

With all your files edited and saved, you should reboot so the new name and configuration will be used.

Reboot the system and then use ifconfig or ipaddr to confirm that your new configuration is available. You can also use hostname -f to verify the hostname change,

  • configure networking, ubuntu networking file, ubuntu interfaces, /etc/network/interfaces, restart interfaces, debian interfaces
  • 684 Користувачі, які знайшли це корисним
Ця відповідь Вам допомогла?

Схожі статті

How to Set Up a Mac for Your Kids

Providing children with access to a computer and the internet is increasingly important, but so...

How to Get Help With a Command from the Linux Terminal

Whether you’re an inexperienced terminal user or a grizzled veteran, you won’t always know the...

How to change the ssh port on Linux

To Change the SSH Port for Linux Server Connect to your server via SSH Switch to the root...

How To Install screenFetch in Linux

If you've browsed Linux groups on social media, you've probably seen a lot of screenshots that...

Static IP vs. Dynamic IP Address

A static IP address is one that remains fixed and never changes. The PC always sees the same...

Powered by WHMCompleteSolution